LilyPad 328 ATmega328P Wearable E-Textile Main Development Board is a circular 50mm wearable microcontroller board designed by Leah Buechley and SparkFun for sewing directly into clothing, costumes, and soft e-textile fabrics using conductive thread. Furthermore, it integrates a low-power Microchip/Atmel ATmega328P-AU microcontroller running at 8 MHz on an wide 2.7V–5.5V supply range alongside a standard 6-pin FTDI serial programming header. Consequently, its 22 large silver-plated perimeter sew tabs let designers stitch washable LEDs, buzzers, light sensors, and LiPo battery holders directly into interactive garments without rigid wires.
Key Features:
- 22 Large Conductive-Thread Sew Tabs: Wide half-moon plated pads around the 50mm circular perimeter allow easy hand-stitching with stainless-steel conductive thread.
- Wide 2.7V to 5.5V Operating Range: Runs at a safe 8 MHz clock speed so it can be powered directly from a single 3.7V LiPo cell, a 3V coin cell, or a 5V LilyPad AAA boost module.
- Flat, Snag-Free Underside Profile: All SMD components, the reset button, and the 6-pin FTDI header are mounted on the top face only, leaving the back smooth against fabric.
- Standard 6-Pin FTDI Auto-Reset Header: Right-angle 6-pin male header (`DTR, RX, TX, VCC, CTS, GND`) connects to any FT232RL / CP2102 / CH340 USB-to-TTL adapter for one-click Arduino IDE uploads.
- Washable Low-Component Design: Omission of bulky linear regulators and USB sockets allows gentle hand-washing of the finished garment once the battery is unplugged.
Technical Specifications:
- Microcontroller: Microchip / Atmel ATmega328P-AU (or ATmega328V, 8-Bit AVR @ 8 MHz Resonator)
- Operating Supply Voltage: 2.7V to 5.5V DC (Connect Directly between `+` and `-` Sew Tabs)
- Digital I/O Sew Tabs: 14 Digital Pins (`2–13, TX, RX`; 6 PWM Channels on `3, 5, 6, 9, 10, 11`)
- Analog Input Sew Tabs: 6 Channels (`A0–A5`, 10-Bit ADC Resolution)
- DC Current per I/O Tab: 20 mA Recommended (40 mA Max)
- Memory: 32 KB Flash (2 KB Bootloader), 2 KB SRAM, 1 KB EEPROM
- Programming Interface: 6-Pin 2.54mm FTDI Serial Header (57600 Baud Bootloader)
Mechanical Specifications:
- PCB Substrate: Thin 0.8mm Signature Purple FR-4 Fiberglass Circular PCB
- Perimeter Pads: 22 × Large Plated Through-Hole Sew Tabs
- Onboard Controls: Top-Mounted SMD Tactile Reset Button + Pin 13 Indicator LED
Dimensions:
- Outer Diameter: 50.0 mm
- PCB Thickness: 0.8 mm (≈ 3.0 mm Total Height at FTDI Header)
- Weight: ≈ 4.5 g
Pinout and Wiring:
- Power Sew Tabs (`+` and `-`): Connect a 3.7V LiPo battery or 5V LilyPad power module between the `+` (VCC) and `-` (GND) tabs.
- 6-Pin FTDI Header (`B / GND` to `G / DTR`): Align the `B` (Black/GND) and `G` (Green/DTR) silkscreen markers with your 3.3V/5V FTDI USB-to-Serial adapter.
- I2C & SPI Sew Tabs: `A4 (SDA) / A5 (SCL)` for I2C accelerometers; `10 (SS), 11 (MOSI), 12 (MISO), 13 (SCK)` for SPI.
- Engineering Precaution: The LilyPad 328 has NO onboard voltage regulator on the `+` tab; never connect a 9V battery or >5.5V supply to the `+` tab, and ensure uninsulated conductive thread traces never cross or touch each other when the fabric folds.
Datasheet Reference:
Commonly Used in:
- Interactive Smart Garments, Cosplay Costumes, and Stage Performance Wearables
- High-Visibility Cycling Jackets with Turn-Signal LEDs and Accelerometer Brake Lights
- E-Textile Design, STEAM Fashion Technology, and Soft-Circuit Workshops
Applications:
- Sewable LED & Sensor Networks: Stitches directly to LilyPad White/RGB LEDs, LilyPad Slide Switches, and LilyPad Button modules using conductive thread.
- Ultra-Light LiPo Projects: Runs for hours on a tiny 100mAh–500mAh 3.7V LiPo pouch cell paired with a LilyPad 5V LiPo Boost module.
- Soft Plush & Educational Toys: Embeds touch, tilt, and sound interactivity inside fabric plushies without sharp PCB corners.
Equivalent Models:
- LilyPad USB (ATmega32U4): Upgraded circular LilyPad board with a built-in Micro-USB port and JST LiPo charger IC.
- Adafruit Flora / Gemma M0: Circular wearable boards featuring NeoPixel LEDs and native USB.
- Arduino Pro Mini 3.3V/8MHz: Uses the same 8MHz ATmega328P configuration in a rectangular 2.54mm through-hole PCB for soldered wire harnesses.
Package Includes:
- 1 × LilyPad 328 ATmega328P Wearable E-Textile Main Development Board

Reviews
No reviews yet. Be the first to share your experience!