Back to Category
Shop By Departments

DRV8825 / A4988 Single-Axis NEMA 17 (42) Stepper Motor Driver Expansion Shield

₹85.00

In stock ?

Category: Brand:

DRV8825 / A4988 Single-Axis NEMA 17 (42) Stepper Motor Driver Expansion Shield is a compact carrier and breakout adapter board engineered to host a single Pololu-pinout A4988, DRV8825, or TMC2208 stepper motor driver module. Furthermore, it integrates a 3-position DIP switch for hardware microstepping selection (`MS1, MS2, MS3`), an onboard 100µF 50V electrolytic bulk decoupling capacitor, a 4-pin JST-XH motor output socket, and a 2-pin DC power terminal. Consequently, it eliminates breadboard wiring burnout by safely routing high-current 12V–30V motor power and logic signals (`EN, DIR, STEP`) to drive 42-series (NEMA 17) bipolar stepper motors.

Key Features:
  • Universal 16-Pin StepStick Socket: Female 2×8 2.54mm socket accepts standard A4988 (up to 1/16 step), DRV8825 (up to 1/32 step), and TMC2100/TMC2208 stepper driver modules.
  • Onboard 3-Bit Microstepping DIP Switch: Built-in 3-way slide DIP switch (`S1, S2, S3`) configures full-step, 1/2, 1/4, 1/8, 1/16, or 1/32 microstepping cleanly without jumper caps.
  • Integrated 100µF High-Voltage Decoupling Capacitor: Protects the plugged-in driver IC against destructive inductive LC voltage spikes on the `VMOT` motor supply rail.
  • Built-In 5V Logic Supply Pass-Through: Regulates or distributes 5V logic power (`VDD`) and ties `SLEEP` and `RESET` properly so only `EN, DIR, STEP`, and `GND` need to connect to your Arduino.
  • Standard 4-Pin NEMA 17 Motor Header: Plugs directly into standard 4-wire bipolar stepper motor harnesses (`2B, 2A, 1A, 1B`).
Technical Specifications:
  • Compatible Driver Modules: A4988, DRV8825, TMC2100, TMC2208, TMC2209 (16-Pin Pololu Pinout)
  • Motor Supply Voltage (`VMOT`): 8.2V to 30.0V DC (12V–24V DC Recommended for A4988/DRV8825)
  • Logic Supply Voltage (`5V / VDD`): 3.3V to 5.0V DC
  • Supported Motor Type: 2-Phase 4-Wire Bipolar Stepper Motors (42mm NEMA 17, 28mm NEMA 11, 35mm NEMA 14)
  • Control Signal Inputs: 4-Pin Male Header (`GND, 5V, EN, DIR, STEP`)
  • Microstep Selection: 3-Way Onboard DIP Switch (`MS1, MS2, MS3`)
Mechanical Specifications:
  • PCB Substrate: Double-Sided Red/Black FR-4 Fiberglass PCB with Heavy Copper Motor Power Traces
  • Connectors: 2×8 Female Driver Socket, 4-Pin XH2.54 Motor Connector, 2-Pin Power Input Header, 3-Way DIP Switch
  • Mounting Holes: 4 × 3.0mm Corner Mounting Holes
Dimensions:
  • Length: 42.0 mm
  • Width: 32.0 mm
  • Height: 14.0 mm
  • Weight: ≈ 11 g
Pinout and Wiring:
  • Driver Orientation (CRITICAL): Match the `EN` (Enable) and `VMOT` pins of your A4988 or DRV8825 module with the silkscreen labels on the underside/top of the expansion board (note that the current-limit potentiometer faces OPPOSITE directions on A4988 vs DRV8825!).
  • Motor Output (`2B, 2A, 1A, 1B`): Connect Coil B across `2B/2A` and Coil A across `1A/1B`.
  • Control Header (`EN, DIR, STEP`): Connect `STEP` and `DIR` to two Arduino digital pins; pull `EN` LOW (or leave enabled) to energize the motor coils.
  • Engineering Precaution: NEVER plug or unplug the 4-pin stepper motor cable while the 12V/24V `VMOT` power supply is turned ON, as breaking an energized inductive motor coil will instantly destroy the A4988/DRV8825 MOSFET bridge.
Datasheet Reference:
Commonly Used in:
  • Single-Axis Linear Actuators, Camera Slider Rails, and Rotary Turntables
  • Automated Syringe Pumps, Coil Winders, and Wire-Stripping Machines
  • Standalone NEMA 17 Stepper Motor Test Benches with Arduino UNO / Nano
Applications:
  • Single-Axis Motion Control: Drives a single NEMA 17 lead-screw actuator without needing a full 4-axis CNC Shield V3.
  • Microstepping Evaluation: Toggles between 1/1, 1/2, 1/4, 1/8, 1/16, and 1/32 microstepping via the 3-way DIP switch to optimize torque vs acoustic noise.
  • Rapid Driver Swapping: Allows hot-swapping (with power off) between A4988, DRV8825, and silent TMC2208 modules in seconds.
Equivalent Models:
  • CNC Shield V3 Expansion Board for Arduino UNO: Full 4-axis shield hosting up to 4 × A4988/DRV8825 modules simultaneously for X/Y/Z/A machines.
  • CNC Shield V4 Expansion Board for Arduino Nano: 3-axis stepper driver carrier shield designed for the Arduino Nano.
  • TB6600 4A Stepper Motor Driver Controller: Enclosed standalone 9V–42V 4A driver for larger NEMA 23 and high-torque NEMA 17 motors.
Package Includes:
  • 1 × DRV8825 / A4988 Single-Axis NEMA 17 (42) Stepper Motor Driver Expansion Shield
Weight 20 g
Dimensions 42 × 42 × 10 mm

Questions and Answers

No questions have been asked about this product yet. Be the first!


Ask a Question

Average Rating
0.00
0 Reviews
5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Be the first to review “DRV8825 / A4988 Single-Axis NEMA 17 (42) Stepper Motor Driver Expansion Shield”

You must be logged in to post a review.

Reviews

No reviews yet. Be the first to share your experience!

DRV8825 / A4988 Single-Axis NEMA 17 (42) Stepper Motor Driver Expansion Shield

DRV8825 / A4988 Single-Axis NEMA 17 (42) Stepper Motor Driver Expansion Shield

₹85.00
Hi, How can I help you today?
Chat Assistant