L293D Dual H-Bridge Motor Driver Board is a versatile dual-channel DC motor and stepper motor driver board engineered around the industry-standard L293D quadruple high-current half-H driver IC. Designed for educational robotics, smart car platforms, and maker prototypes, this module incorporates an onboard LM7805 5V linear voltage regulator, power indicator LED, motor power switch, and convenient male header breakout pins. It enables independent bidirectional speed and direction control of two DC brushed motors (up to 36V DC, 600mA continuous per channel) or one 4-wire bipolar stepper motor without requiring separate logic power supplies.
Key Features:
- Dual H-Bridge Driver Architecture: Powered by the L293D IC to provide independent bidirectional control for two DC motors or one bipolar stepper motor.
- Onboard 5V Voltage Regulation: Integrated LM7805 voltage regulator supplies clean 5V logic power directly from the main motor power input rail.
- User-Accessible Enable Pins: Separate hardware jumper pins for Channel A and Channel B enable straightforward PWM speed modulation.
- Convenient Header Breakout: Standard 2.54mm male header pins ensure quick, solderless jumper wire hookup to Arduino, Raspberry Pi, and ESP32 boards.
- Onboard Power Management: Features a dedicated master power sliding switch and power indicator LED for rapid benchtop troubleshooting.
Technical Specifications:
- Motor Operating Voltage (VCC): 4.5V to 36V DC
- Logic Operating Voltage (VSS): 5.0V DC (generated onboard or externally fed)
- Continuous Drive Current: 600 mA per channel
- Peak Surge Output Current: 1.2 A per channel (non-repetitive)
- Logic Input Voltage Range: High (2.3V to 7V), Low (-0.3V to 1.5V)
- Maximum PWM Frequency: Up to 5 kHz
- Operating Temperature Range: 0°C to +70°C
Mechanical Specifications:
- Board Material: High-quality double-sided FR4 PCB with silkscreen labeling
- Terminal Blocks: 2-pin screw terminals for motor outputs and power inputs
- Header Pitch: Standard 2.54 mm (0.1 inch) male pin headers
- Mounting Support: 4 × M3 mounting holes positioned at board corners
Dimensions:
- Length: 48.0 mm
- Width: 36.0 mm
- Height: 18.0 mm
- Weight: Approximately 28 g
Pinout and Wiring:
- VCC / +12V: Main positive power input for motors (4.5V to 36V DC).
- GND: Common system ground connected to power supply and microcontroller ground.
- 5V: Regulated 5V output (when jumpered) or logic input pin.
- IN1 / IN2: Logic directional input pins for Motor Channel A.
- IN3 / IN4: Logic directional input pins for Motor Channel B.
- ENA / ENB: Speed control PWM enable jumpers for Channels A and B.
- OUT1 / OUT2 (Motor A): Screw terminal connection for Motor A.
- OUT3 / OUT4 (Motor B): Screw terminal connection for Motor B.
Datasheet Reference:
Commonly Used in:
- Educational Robotics: Two-wheel differential drive robotic kits and STEM obstacle avoiders.
- Line Following Robots: Direct integration with multi-channel infrared sensor arrays.
- Pan-Tilt Camera Platforms: Precision low-power DC gearmotor positioning.
Applications:
- Small DC Motor Actuation: Bidirectional forward, reverse, coast, and brake control for N20, TT, and 130/260-size motors.
- Unipolar/Bipolar Stepper Driving: Four-phase sequential stepping for miniature 28BYJ-48 or NEMA 14 stepper motors.
- Solenoid and Relay Actuation: Inductive load switching with integrated internal clamp diodes.
Equivalent Models:
- L298N Dual H-Bridge Module: High-power successor delivering up to 2A continuous current per channel for larger DC motors and high-torque robots.
- TB6612FNG Motor Driver Module: High-efficiency MOSFET-based driver delivering 1.2A per channel with significantly lower voltage drop and less thermal dissipation.
- L9110S Dual Channel Driver: Ultra-compact, low-voltage (2.5V-12V) driver module optimized for battery-operated miniature toy robotics.
Package Includes:
- 1 × L293D Dual H-Bridge Motor Driver Board

Reviews
No reviews yet. Be the first to share your experience!