5S 18.5V 21V 18650 Li-ion Battery Passive Equalizer Balancer Board is an auxiliary 5-series (5S 18.5V nominal / 21.0V full charge) cell voltage equalization module designed to add 4.20V per-cell charge balancing to 5S lithium-ion battery packs whose primary BMS lacks a built-in balancing circuit. Whenever any individual cell in a 5S pack reaches 4.20V during charging, that channel’s precision voltage detector activates a 66mA bleed resistor to shunt excess charging current around the full cell until the remaining cells catch up to 4.20V.
Key Features:
- Adds 5-Channel Balancing to Non-Balanced 5S BMS Packs: Works alongside any standard 5S BMS (`PID 23357` or `PID 29823`) to ensure all 5 series cells reach 4.20V uniformly at the end of every charge cycle.
- Precision 4.20V Per-Cell Activation Threshold: Each of the 5 channels independently monitors its cell and begins shunting current as soon as that cell reaches 4.20V.
- 66mA Shunt Balance Current per Channel: High-power SMD bleed resistors safely bypass 66mA per cell (`4.2V / 62Ω ≈ 66mA`) to prevent early single-cell overcharge cutoff on the main BMS.
- Zero Standby Drain Below 4.20V: Consumes virtually zero current during normal battery discharging or storage below 4.18V/cell.
- Ultra-Compact Solder-Pad Strip: Tiny footprint tucks right beside your existing 5S BMS inside shrink-wrapped 18650 packs.
Technical Specifications:
- Supported Pack Configuration: 5S (5 Series 3.7V Li-ion / 18650 / 21700 / LiPo Cells — 18.5V Nominal / 21.0V Full)
- Single-Cell Balance Trigger Voltage: 4.20V DC per cell
- Single-Cell Balance Current: 66 mA per channel
- Recommended BMS Overcharge Cut-Off: Pair with a 5S BMS whose overcharge cutoff is ≥ 4.25V/cell so the 4.20V balancer activates before the BMS trips
- Recommended Cell Matching: Internal resistance difference ≤ 5 mΩ, initial voltage within 0.03V, capacity within 50 mAh
Mechanical Specifications:
- PCB Material: FR-4 Fiberglass Strip PCB with 5 × Precision Shunt Channels
- Terminals: 6 × Tinned Solder Pads (`B-`, `B1`, `B2`, `B3`, `B4`, `B5`)
Dimensions:
- Length: ~38 mm
- Width: ~26 mm
- Thickness: ~2.5 mm
- Weight: ~4 g
Pinout and Wiring:
- B- (0V): Connect to Cell 1 Negative (Pack Negative).
- B1 (3.7V): Connect between Cell 1+ and Cell 2-.
- B2 (7.4V): Connect between Cell 2+ and Cell 3-.
- B3 (11.1V): Connect between Cell 3+ and Cell 4-.
- B4 (14.8V): Connect between Cell 4+ and Cell 5-.
- B5 / B+ (18.5V/21V): Connect to Cell 5 Positive (Pack Positive).
- Important Note: This is an auxiliary charge equalizer board only—it does NOT provide over-discharge or short-circuit cutoff, so always use it in parallel with a 5S BMS protection board!
Datasheet Reference:
- Circuit Architecture: 5 × Independent 4.20V Precision Voltage Detectors + MOSFET Switches + $6262 Ω SMD Bleed Resistors (66mA)
Commonly Used in:
- Upgrading Non-Balanced 5S 18.5V / 21V Cordless Drill Battery Packs
- 5S1P / 5S2P / 5S3P 18650 E-Scooter & Vacuum Packs
- 21V Solar Storage & Portable Power Packs
- Extending Cycle Life of Series 18650 Packs
Applications:
- Wires directly in parallel with the `B-` through `B+` sense leads of a 5S 15A BMS to add 66mA/cell top-balancing.
- Prevents capacity drift where one cell hits 4.25V early and forces the BMS to stop charging while the other 4 cells are still at 4.05V.
- Restores full usable runtime to 18V/21V cordless tool battery packs.
Equivalent Models:
- 4S 14.8V Li-ion Balancer Board: 4-series (14.8V/16.8V) 66mA passive balancer board (`PID 2145`).
- 6S 4.2V Li-ion Balancer Board: 6-series (22.2V/25.2V) 66mA passive balancer board (`PID 3362`).
Package Includes:
- 1 × 5S 18.5V 21V 18650 Li-ion Battery Passive Equalizer Balancer Board

Reviews
No reviews yet. Be the first to share your experience!