Back to Category
Shop By Departments

XH-M609 DC 12V-36V Battery Low Voltage Over-Discharge Protection Module

₹349.00

In stock ?

In stock

SKU: 999-5-08 Category: Brand:

XH-M609 DC 12V-36V Battery Low Voltage Over-Discharge Protection Module is a programmable digital battery undervoltage disconnect switch designed to protect 12V, 24V, and 36V lead-acid, lithium-ion, LiFePO4, and solar storage batteries from destructive deep discharge. Equipped with a bright 3-digit LED voltmeter display, two tactile programming buttons, and a high-current onboard power relay, the XH-M609 continuously monitors battery input voltage and automatically disconnects the output load the moment voltage falls below the user-defined cut-off threshold (0.1V resolution).

Key Features:
  • Wide 12V to 36V DC Operating Range: Compatible with 12V, 24V, and 36V lead-acid, SLA, AGM, Li-ion, and LiFePO4 battery banks.
  • 0.1V Precision Digital Programming: Dual tactile buttons (+ and -) configure exact disconnect voltage, hysteresis recovery voltage, and delayed turn-on timers.
  • 3-Digit LED Real-Time Voltmeter: Displays live battery terminal voltage and flashes during low-voltage cut-off warnings.
  • Non-Volatile Parameter Memory: All user-configured cut-off and hysteresis settings are stored in EEPROM and retained across power cycles.
  • One-Key Factory Reset: Holding both + and – buttons simultaneously for 3 seconds restores default factory protection parameters.
Technical Specifications:
  • Model: XH-M609 Digital Battery Undervoltage Protection Module
  • Input Supply Voltage: 12V to 36V DC (6V–40V maximum operating limits)
  • Output Voltage: Equal to Input Battery Voltage (Direct Relay Switch)
  • Maximum Relay Load Current: 10A Continuous (at ≤12V) / <8A (at 24V–36V)
  • Voltage Measurement & Control Precision: 0.1 V
  • Quiescent Power Consumption: < 1.5 W
  • Delayed Turn-On Timer Range: 0 to 10 minutes adjustable
  • Operating Temperature Range: -20°C to +75°C
Mechanical Specifications:
  • Display: 0.36-inch 3-Digit 7-Segment Red LED Digital Tube
  • Terminals: 2 × 2-pin heavy-duty screw terminal blocks (VIN+/VIN- and OUT+/OUT-)
  • Controls: 2 × Tactile pushbuttons (Left: Start/Cut-off Set; Right: Hysteresis/Difference Set)
  • Mounting Holes: 4 × 3.0mm corner mounting holes
  • Weight: Approximately 28 grams
Dimensions:
  • Length: 57.0 mm
  • Width: 42.0 mm
  • Height: 19.0 mm
Pinout and Wiring:
  • VIN+ (Battery +): Connect to 12V–36V Storage Battery Positive terminal.
  • VIN- (Battery -): Connect to Storage Battery Negative terminal.
  • OUT+ (Load +): Switched Positive Output to DC load (Disconnected when battery is below cut-off voltage).
  • OUT- (Load -): Negative Output to DC load (Internally common with VIN-).
  • Programming Guide: Double-click (+) to set Low-Voltage Cut-off value; Double-click (-) to set Hysteresis Difference value (Reconnect Voltage = Cut-off + Difference).
Datasheet Reference:
  • Refer to the XH-M609 Digital Over-Discharge Protection Module instruction sheet for voltage calibration, delay timer, and hysteresis setup.
Commonly Used in:
  • 12V/24V solar off-grid battery banks and DC lighting load disconnects
  • Automotive 12V auxiliary accessories (fridges, dashcams, inverters) to prevent starter battery drain
  • 24V/36V electric scooter, e-bike, and mobility cart battery undervoltage protection
  • Uninterruptible DC power supplies and telecom battery backup racks
Applications:
  • Deep-Discharge Battery Protection: Automatically cutting off DC loads before lead-acid sulfation or lithium cell degradation occurs.
  • Hysteresis Load Cycling: Preventing relay chatter by requiring battery voltage to recover by a programmed delta before reconnecting the load.
  • Solar Load Management: Disconnecting non-essential loads at night when solar battery voltage sags.
Equivalent Models:
  • 12V LM358 Over-Discharge Controller: Analog potentiometer-adjusted 12V low-voltage disconnect relay board.
  • XH-M603 Digital Charge Controller: Similar digital relay module configured for battery charging cut-off rather than load discharge cut-off.
  • XY-L10A LCD Battery Controller: 6V–60V LCD battery controller supporting charge/discharge control with UART output.
Package Includes:
  • 1 × XH-M609 DC 12V-36V Battery Low Voltage Over-Discharge Protection Module
Weight 30 g
Dimensions 60 × 40 × 20 mm

Questions and Answers

No questions have been asked about this product yet. Be the first!


Ask a Question

Average Rating
5.00
1 Review
5 Star
100%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Add a review

You must be logged in to post a review.

1 Review For This Product

  1. by Rajesh Gopi | August 16, 2022

    Good item..

XH-M609 DC 12V-36V Battery Low Voltage Over-Discharge Protection Module

XH-M609 DC 12V-36V Battery Low Voltage Over-Discharge Protection Module

₹349.00
Hi, How can I help you today?
Chat Assistant