Back to Category
Shop By Departments

12V 10A Lead-Acid Battery Over-Discharge Protection Cut-Off Module

₹149.00

In stock ?

In stock

12V 10A Lead-Acid Battery Over-Discharge Protection Cut-Off Module is a zero-standby-drain latching relay undervoltage cut-off protector designed specifically for 12V lead-acid, SLA, AGM, and gel storage batteries. Because discharging a 12V lead-acid battery below 10.5V causes irreversible lead-sulfate crystallization and capacity loss, this module monitors battery voltage continuously and drops out its 10A relay at ~10.7V (±0.15V), completely disconnecting both the external load and the module’s own coil circuit so zero current is drawn from the depleted battery.

Key Features:
  • Zero-Drain Complete Cut-Off at ~10.7V: When battery voltage falls to 10.7V ±0.15V, the relay releases and disconnects power to both the load and the protection circuit itself—eliminating parasitic standby drain on an already empty battery!
  • Push-Button Manual Start Latch: Features an onboard tactile start button that latches the 10A relay ON when battery voltage is healthy (>11V), preventing chatter/oscillation when battery voltage rebounds slightly after load removal.
  • 10A High-Current Relay Output: Switches up to 10A DC loads (120W at 12V) cleanly via heavy-duty screw terminals (`IN+`, `GND`, `OUT+`).
  • Active Status LED Indicator: Onboard LED illuminates whenever the protection relay is latched ON and extinguishes upon low-voltage cutoff.
  • Works with Any Capacity 12V Lead-Acid Battery: Compatible with 12V 1.3Ah, 4.5Ah, 7Ah, 12Ah, 35Ah, and 100Ah+ lead-acid batteries.
Technical Specifications:
  • Compatible Battery Type: 12V Lead-Acid / SLA / VRLA / AGM / Gel Batteries (Any Ah Capacity)
  • Undervoltage Cut-Off Threshold: ~10.7V ± 0.15V DC
  • Maximum Relay Control Current: 10A DC
  • Cut-Off Standby Current: 0 mA (Zero Drain after Relay Releases)
  • Activation Method: Onboard Push-Button Momentary Trigger Switch
  • Operating Temperature Range: -20°C to +70°C
Mechanical Specifications:
  • PCB Material: FR-4 Fiberglass Board
  • Terminals: 3-Pin Screw Terminal Block (`IN+`, `GND`, `OUT+`)
  • Controls: 1 × Tactile Start Push Button + 1 × Status LED
Dimensions:
  • Length: ~50 mm
  • Width: ~30 mm
  • Height: ~18 mm
  • Weight: ~18 g
Pinout and Wiring:
  • IN+: Connect to 12V battery positive (+) terminal.
  • GND: Common negative — connect to both 12V battery negative (-) and load negative (-).
  • OUT+: Switched positive output — connect to 12V load positive (+).
  • Operation: With a charged 12V battery connected, press the onboard push button once; the relay clicks ON, the LED lights up, and power flows to `OUT+`. When the battery discharges down to 10.7V, the relay clicks OFF and stays OFF until the battery is recharged and the button is pressed again.
Datasheet Reference:
  • Circuit Architecture: Precision Zener/TL431 Voltage Sense + Self-Latching 12V 10A Relay Cut-Off Circuit
Commonly Used in:
  • 12V 7Ah / 12Ah UPS & Emergency Lantern Battery Protection
  • Portable 12V Agricultural Sprayers, Camping Lights, and Fans
  • Automotive & Motorcycle Auxiliary Accessory Cut-Offs
  • Benchtop 12V Battery Discharge Testing Setups
Applications:
  • Prevents accidental overnight total discharge of 12V 7Ah SLA batteries powering camping LED lamps or DC fans.
  • Eliminates relay “bouncing” (turning ON and OFF repeatedly as unloaded battery voltage bounces back from 10.5V to 11.8V) thanks to its manual push-button reset latch.
  • Extends 12V lead-acid battery service life by 2×–3× by strictly enforcing a 10.7V discharge floor.
Equivalent Models:
  • 12V Battery Undervoltage Management Module: Potentiometer-adjustable 12V 10A undervoltage module with automatic voltage-recovery turn-on.
  • 12V LM358 Accumulator Over Discharge Controller Without Overvoltage Protection Board: LM358 comparator-based 12V low-voltage cut-off module with buzzer alarm.
Package Includes:
  • 1 × 12V 10A Lead-Acid Battery Over-Discharge Protection Cut-Off Module
Weight 15 g

Questions and Answers

No questions have been asked about this product yet. Be the first!


Ask a Question

Average Rating
0.00
0 Reviews
5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Be the first to review “12V 10A Lead-Acid Battery Over-Discharge Protection Cut-Off Module”

You must be logged in to post a review.

Reviews

No reviews yet. Be the first to share your experience!

12V 10A Lead-Acid Battery Over-Discharge Protection Cut-Off Module

12V 10A Lead-Acid Battery Over-Discharge Protection Cut-Off Module

₹149.00
Hi, How can I help you today?
Chat Assistant