Back to Category
Shop By Departments

XH-M601 12V Battery Charging Control Board

₹160.00

In stock ?

In stock

XH-M601 12V Battery Charging Control Board is an automated voltage-sensing relay charge controller module designed for 12V lead-acid, SLA, VRLA, and AGM storage batteries. Operating around an onboard comparator circuit and a heavy-duty 220V AC 10A mechanical relay, this module continuously monitors battery terminal voltage to automatically switch an external AC battery charger ON when the battery drops below a low-voltage threshold (default ~10.5V–11.5V) and OFF once full charge voltage (default ~13.8V–14.4V) is reached. Two multi-turn precision trimmer potentiometers (RP1 and RP2) allow full manual calibration of the start and stop voltage thresholds.

Key Features:
  • Fully Automatic Start/Stop Relay Control: Connects and disconnects the external AC power supply to the charger automatically based on real-time battery voltage.
  • Dual Precision Trimpots (RP1 & RP2): Multi-turn 3296W potentiometers independently adjust low-voltage start-charging and high-voltage stop-charging setpoints.
  • 10A High-Capacity Relay Switch: Switches AC 220V mains input to an external charger transformer or DC charging bus up to 10A.
  • Self-Powered from Monitored Battery: Draws operating power directly from the connected 12V battery under test without requiring an auxiliary logic supply.
  • Dual LED Status Indicators: Onboard Red power LED and Green charging-relay active LED provide clear visual feedback.
Technical Specifications:
  • Model: XH-M601 Intelligent Battery Charging Control Module
  • Target Battery Voltage: 12V Nominal Storage Batteries (Lead-Acid, SLA, VRLA, Gel, AGM)
  • Supply Voltage Range: 10.0V to 15.0V DC (Powered directly from battery terminals)
  • Voltage Control Accuracy: ± 0.1 V
  • Relay Contact Rating: 10A at 250V AC / 10A at 30V DC
  • Start Charging Adjustment (RP1): Clockwise increases start voltage; counter-clockwise decreases
  • Stop Charging Adjustment (RP2): Clockwise increases stop voltage; counter-clockwise decreases
  • Quiescent Power Consumption: < 1.5 W
Mechanical Specifications:
  • PCB Material: FR-4 Double-Sided Fiberglass Board
  • Connectors: 2-pin screw terminal block for 12V battery sensing/charging and 2-pin AC relay switching terminal block
  • Mounting Holes: 4 × 3.2mm corner mounting holes for enclosure installation
  • Weight: Approximately 28 grams
Dimensions:
  • Length: 50.0 mm
  • Width: 32.0 mm
  • Height: 18.0 mm
Pinout and Wiring:
  • BAT+ / BAT- Screw Terminal: Connect directly to the 12V Battery Positive (+) and Negative (-) terminals (Observe strict polarity).
  • 220V AC Relay Terminal Block: Wired in series with the AC live wire feeding your external 12V battery charger/rectifier.
  • RP1 Trimmer: Adjusts the Low-Voltage Start-Charging threshold.
  • RP2 Trimmer: Adjusts the High-Voltage Stop-Charging cut-off threshold.
Datasheet Reference:
  • Refer to the XH-M601 12V Automatic Battery Charge Controller calibration guide and LM358 voltage comparator schematic.
Commonly Used in:
  • 12V automotive, motorcycle, and inverter backup lead-acid battery chargers
  • Uninterruptible Power Supply (UPS) float-charge cutoff retrofits
  • Solar and wind off-grid 12V storage battery overcharge protection relays
  • Generator starter battery automatic maintenance chargers
Applications:
  • Automated Charger Cut-off: Upgrading manual 12V transformer battery chargers with automatic full-charge shutoff.
  • Battery Overcharge Prevention: Protecting sealed lead-acid (SLA) batteries from electrolyte boiling and sulfation.
  • Backup Power Maintenance: Keeping standby emergency batteries automatically topped between 12.0V and 14.4V.
Equivalent Models:
  • XH-M603 12V–24V Digital Charge Control Module: Upgraded digital version with 3-digit LED voltage display and pushbutton setpoint programming.
  • XH-M604 6V–60V Digital Charge Controller: Wide-voltage digital relay charger controller supporting 12V, 24V, 36V, and 48V battery banks.
  • XY-L10A 6V–60V LCD Charge Controller: Backlit LCD charge controller with charge-time limit and UART communication.
Package Includes:
  • 1 × XH-M601 12V Battery Charging Control Board
Weight 25 g
Dimensions 50 × 35 × 20 mm

Questions and Answers

No questions have been asked about this product yet. Be the first!


Ask a Question

Average Rating
0.00
0 Reviews
5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Be the first to review “XH-M601 12V Battery Charging Control Board”

You must be logged in to post a review.

Reviews

No reviews yet. Be the first to share your experience!

XH-M601 12V Battery Charging Control Board

XH-M601 12V Battery Charging Control Board

₹160.00
Hi, How can I help you today?
Chat Assistant