TP4056 1A Li-Ion Battery Charging Board Micro USB with Current Protection is a compact single-cell constant-current/constant-voltage (CC/CV) linear lithium-ion battery charger module featuring integrated battery protection circuitry. Equipped with a standard Micro-USB receptacle and solder input pads, this board combines the TP4056 1A linear charge controller with a DW01A battery protection IC and FS8205A dual MOSFET. It provides safe 4.2V charging alongside automatic overcharge, deep-discharge (2.4V cut-off), and 3A overcurrent/short-circuit protection for 18650 and LiPo cells.
Key Features:
- Standard Micro-USB Input: Directly powered from any 5V Micro-USB phone charger, power bank, or PC USB port.
- 1A Constant-Current / Constant-Voltage: Precision linear regulation charges single-cell 3.7V lithium batteries to 4.20V ±1.5%.
- Onboard Battery Protection (DW01A + FS8205A): Dedicated OUT+ and OUT- load terminals disconnect automatically upon over-discharge or short circuit.
- Programmable Charge Current: Default 1A charging current can be reduced for smaller LiPo cells by changing the onboard 1.2kΩ RPROG resistor.
- Dual LED Charge Status Indicators: Red LED illuminates during charging; Blue/Green LED illuminates when charging is complete.
Technical Specifications:
- Charger IC: TP4056 Linear Li-Ion Charger
- Protection Chipset: DW01A + FS8205A Dual N-Channel MOSFET
- Input Voltage Range: 4.5V to 5.5V DC (5V USB nominal)
- Charge Cut-off Voltage: 4.20V ± 1.5%
- Maximum Charging Current: 1000 mA (1A default)
- Overcharge Cut-off / Release Voltage: 4.30V ± 0.05V / 4.10V ± 0.05V
- Over-Discharge Cut-off / Release Voltage: 2.40V ± 0.10V / 3.00V ± 0.10V
- Overcurrent Protection Threshold: 3.0 A
- Operating Temperature Range: -10°C to +85°C
Mechanical Specifications:
- Input Connector: SMD 5-pin Micro-USB Female Port
- PCB Material: FR-4 Double-Sided Fiberglass Board with thermal dissipation pad
- Terminal Pads: 6 through-hole solder pads (IN+, IN-, B+, B-, OUT+, OUT-) at 2.54mm pitch
- Weight: Approximately 1.8 grams
Dimensions:
- Length: 26.0 mm
- Width: 17.0 mm
- Height: 4.0 mm
Pinout and Wiring:
- IN+ / IN-: 5V DC Power Supply Input pads (Parallel to Micro-USB port).
- B+ / B-: Connect directly to the positive and negative terminals of the 3.7V lithium battery.
- OUT+ / OUT-: Protected DC Output terminals for connecting the system load.
Datasheet Reference:
- Refer to the TP4056 1A Standalone Linear Li-Ion Charger Datasheet and DW01A One-Cell Lithium Protection IC Datasheet for resistor programming tables.
Commonly Used in:
- 18650 lithium battery holders and DIY rechargeable power packs
- Battery-powered Arduino, NodeMCU ESP8266, and IoT sensor modules
- Portable Bluetooth audio receivers, mini amplifiers, and LED lanterns
- Student electronics engineering kits and battery management prototypes
Applications:
- Single-Cell Li-Ion/LiPo Charging: Safe 5V USB charging for 18650, 14500, 16340, and pouch lithium polymer cells.
- Deep-Discharge Load Protection: Preventing permanent cell damage by cutting off load power below 2.4V.
- Cordless Device Retrofits: Converting NiCd/NiMH atau AA battery gadgets to rechargeable lithium power.
Equivalent Models:
- TP4056 Type-C Protected Charger Module: Upgraded revision featuring a reversible USB Type-C input connector.
- TP5000 1A Switching Charger Module: Switch-mode step-down charger supporting both 4.2V Li-ion and 3.6V LiFePO4 cells.
- MCP73831 Mini LiPo Charger: Low-current (100mA–500mA) linear charger module for small LiPo pouch batteries.
Package Includes:
- 1 × TP4056 1A Li-Ion Battery Charging Board Micro USB with Current Protection

Reviews
No reviews yet. Be the first to share your experience!