TP4056 1A Micro USB Single Cell Lithium Battery Charging Module is a compact standalone constant-current/constant-voltage (CC/CV) linear charger board for single-cell 3.7V (4.2V full charge) lithium-ion and lithium-polymer batteries. Built around the original TP4056 1A linear charge management IC with a Micro-USB 5V power receptacle, this 4-pad non-protected version is specifically designed for charging cells that already have their own internal protection circuit or for dedicated single-cell charging cradles. It automatically performs 100mA trickle pre-charging for deeply depleted cells (<2.9V), 1A fast charging, and 4.20V ±1.5% float termination.
Key Features:
- Precision TP4056 CC/CV Algorithm: Delivers 1000mA constant-current charging followed by 4.20V constant-voltage saturation and automatic 100mA C/10 termination.
- Automatic Recharge Cycle: Automatically restarts a new charge cycle if the connected battery voltage drops below 4.05V (~80%–90% capacity).
- Deep-Discharge Trickle Recovery: Safely pre-conditions deeply discharged cells (<2.9V) at 100mA before engaging full 1A current.
- Compact 4-Pad Layout: Simplified IN+, IN-, BAT+, and BAT- footprint ideal for tight enclosure spaces.
- Dual LED Charge Indicators: Onboard Red LED indicates active charging; Green/Blue LED indicates full 4.2V charge completion.
Technical Specifications:
- Charger Controller IC: NanJing TopPower TP4056 (SOP-8 with bottom heatsink pad)
- Input Supply Voltage: 4.5V to 5.5V DC (5.0V USB Standard)
- Charge Cut-off Voltage: 4.20V ± 1.5%
- Default Charging Current: 1.0 A (Programmable from 50mA to 1000mA via 1.2kΩ RPROG resistor)
- Pre-Charge Conditioning Threshold: < 2.9V @ 100mA
- Auto-Recharge Threshold: 4.05V
- Operating Temperature Range: -10°C to +85°C
Mechanical Specifications:
- Input Connector: SMD Micro-USB Female Receptacle
- PCB Material: FR-4 Double-Sided Fiberglass Board
- Terminations: 4 through-hole solder pads (IN+, IN-, BAT+, BAT-)
- Weight: Approximately 1.5 grams
Dimensions:
- Length: 22.0 mm
- Width: 17.0 mm
- Height: 3.8 mm
Pinout and Wiring:
- IN+ / +: 5V DC Positive Power Input pad (Parallel to Micro-USB port).
- IN- / -: 5V DC Negative Ground Input pad.
- BAT+ / B+: Connect to 3.7V Lithium Battery Positive (+) terminal.
- BAT- / B-: Connect to 3.7V Lithium Battery Negative (-) terminal.
- Important Note: Observe strict battery polarity (No reverse polarity protection). When charging batteries smaller than 1000mAh, replace the RPROG resistor to keep charge current ≤0.5C.
Datasheet Reference:
- Refer to the NanJing TopPower TP4056 1A Standalone Linear Li-Ion Battery Charger IC Datasheet for RPROG current programming tables.
Commonly Used in:
- Single-slot and multi-slot parallel 18650 battery charging cradles
- Charging protected LiPo pouch batteries that already include an onboard PCM strip
- DIY rechargeable LED torches, emergency lamps, and handheld cooling fans
- Educational electronics labs and battery charging experiments
Applications:
- 18650 & 21700 Cell Charging: Dedicated 5V USB charging for cylindrical lithium-ion cells.
- Embedded Charger Retrofits: Adding Micro-USB charging to battery-operated consumer devices.
Equivalent Models:
- TP4056 1A Protected Module (with DW01A): 6-pad version adding onboard over-discharge and short-circuit load protection.
- TP5000 1A Switch-Mode Charger: High-efficiency buck charger supporting both 4.2V Li-ion and 3.6V LiFePO4 cells.
Package Includes:
- 1 × TP4056 1A Micro USB Single Cell Lithium Battery Charging Module


Reviews
No reviews yet. Be the first to share your experience!