XY-L10A 6V-60V 10A Solar and Storage Battery Charge Controller Module with LCD Display

XY-L10A 6V-60V 10A Solar and Storage Battery Charge Controller Module with LCD Display is an intelligent digital battery charge cutoff controller with a backlit LCD screen designed for 6V to 60V DC lead-acid, lithium-ion, LiFePO4, and solar storage battery systems. Capable of switching up to 10A continuous charging current (30A peak relay rating), the XY-L10A continuously displays real-time battery voltage, charge percentage (%), and elapsed charging time while automatically engaging the charging relay when battery voltage drops below the lower limit (dn) and disconnecting when it reaches the upper limit (UP).

Key Features:

• Backlit Multi-Parameter LCD Screen: Simultaneously displays battery voltage, state-of-charge percentage (%), and charging time on a clear digital LCD.
• Ultra-Wide 6V to 60V DC Compatibility: Supports 6V, 12V, 24V, 36V, 48V, and 60V lead-acid, lithium, and solar battery banks.
• Programmable Charge Time Control (OP): Optional safety timer limits maximum continuous charging duration from 1 minute up to 999 minutes.
• Serial UART Communication & Parameter Upload: TTL UART interface allows remote status monitoring and threshold configuration from a microcontroller or PC.
• Automated Overcharge & Dry-Run Protection: Prevents battery overcharging and isolates the charger if an abnormal charging curve is detected.

Technical Specifications:

• Model: XY-L10A Digital LCD Battery Charge Control Module
• Control Voltage Range: 6.0V to 60.0V DC
• Continuous Control Current: 10 A (Relay Contact Peak Rating: 30 A)
• Voltage Measurement Accuracy: 0.1 V
• Output Type: Direct Voltage Output (Series Relay Switch between Charger and Battery)
• Voltage Error Calibration Range: ± 0.1V to ± 10V
• Communication Interface: 3.3V / 5V TTL UART (115200 bps)
• Operating Temperature Range: -20°C to +70°C

Mechanical Specifications:

• Display: Custom Segment LCD with Blue/White LED Backlight
• Pushbuttons: 3 × Tactile Programming Keys (SET, UP, DOWN)
• Terminals: 4-Position High-Current Barrier Screw Terminal Block (VIN+, VIN-, BAT+, BAT-)
• Mounting Holes: 4 × 3.0mm corner mounting holes
• Weight: Approximately 42 grams

Dimensions:

• Length: 79.0 mm
• Width: 42.0 mm
• Height: 18.0 mm

Pinout and Wiring:

• VIN+ (Charger +): Connect to Positive DC output of the DC power supply or solar panel (Must be higher than full battery voltage).
• VIN- / GND: Common Negative Ground terminal for both Charger and Battery.
• BAT+ (Battery +): Connect to Positive terminal of the 6V–60V Battery Bank.
• Button Operation: Short-press SET to view parameters; Long-press SET (3s) to enter setting mode (UP = Full Charge Stop Voltage, dn = Low Voltage Start Voltage, OP = Charge Time Limit).

Datasheet Reference:

• Refer to the XY-L10A / XY-L30A Digital LCD Battery Charge Controller User Manual for UART AT command syntax and parameter setup.

Commonly Used in:

• 12V/24V/48V solar storage battery banks and off-grid inverter systems
• 36V and 48V electric bicycle, scooter, and golf cart battery charger cutoff retrofits
• Industrial backup generator starter batteries and telecom DC UPS cabinets
• Laboratory automated battery charging rigs with UART data logging

Applications:

• Automated Multi-Voltage Charging: Converting constant-current DC power supplies into smart auto-cutoff chargers for any 6V–60V battery chemistry.
• Timed Safety Charging: Enforcing a maximum charge time window (OP) alongside voltage thresholds for unattended lithium packs.

Equivalent Models:

• XH-M603 12V–24V Charge Control Module: 3-digit LED display charge controller for 12V to 24V battery systems.
• XH-M604 6V–60V Charge Control Board: LED-display equivalent without LCD percentage/timer readout.
• XH-M601 12V Relay Charger Board: Analog trimmer-adjusted 12V battery charge controller.

Package Includes:

• 1 × XY-L10A 6V-60V 10A Solar and Storage Battery Charge Controller Module with LCD Display