Back to Category
Shop By Departments

XD-216 Screw Shield V1 Two-Piece Terminal Expansion Board Set for Arduino UNO

₹249.00

In stock ?

In stock

SKU: SHIELD-2-11 Category: Brand:

XD-216 Screw Shield V1 Two-Piece Terminal Expansion Board Set for Arduino UNO is a split two-wing screw terminal adapter set (`Left Wing + Right Wing`) that plugs into the two outer header banks of an Arduino UNO R3, Leonardo, or Duemilanove. Furthermore, because it consists of two independent winged PCBs rather than a full-width bridge board, it leaves the center of the Arduino UNO completely open for airflow, IC access, ICSP programming, and stacking another full-size Arduino shield directly on top via its pass-through female headers. Consequently, it delivers secure 3.5mm screw-terminal field wiring while maintaining 100% vertical shield stackability.

Key Features:
  • Open-Center Two-Wing Split Architecture: Two separate PCBs plug into the Digital (`D0–D13`) and Power/Analog (`RST–VIN / A0–A5`) sides without covering the ATmega328P chip or 6-pin ICSP header.
  • Pass-Through Female Stacking Headers: Long-pin female headers pass every signal straight through to the top so you can stack an Ethernet, Motor, or LCD shield above the screw terminals.
  • Heavy-Duty 3.5mm Pitch Screw Terminals: Industrial-grade rising-clamp screw blocks grip 16–26 AWG solid or stranded wires tightly against vibration and pull-out.
  • Extra GND & Power Terminal Positions: Includes auxiliary ground screw terminals for terminating shielded sensor cables cleanly.
  • Zero-Soldering Pre-Assembled Set: Both the Left and Right wing boards arrive 100% factory-soldered and ready to plug into your Arduino UNO.
Technical Specifications:
  • Model: XD-216 Screw Shield V1 (2-Piece Split Wing Set)
  • Compatible Host Boards: Arduino UNO R3, Leonardo, Duemilanove, andUNO-Footprint Clones
  • Digital Wing Terminals: `D0 (RX)` through `D13`, `GND`, and `AREF`
  • Analog & Power Wing Terminals: `A0` through `A5`, `VIN`, `GND`, `5V`, `3.3V`, and `RESET`
  • Screw Terminal Pitch: 3.5 mm Pitch Rising-Clamp Terminals
  • Header Pin Pitch: Standard 2.54 mm (0.1 inch) Stackable Female Headers
  • Wire Gauge Capacity: 16 AWG to 26 AWG
Mechanical Specifications:
  • PCB Construction: 2 × Double-Sided Red/Blue FR-4 Fiberglass Wing PCBs
  • Terminal Orientation: Side-Entry Outward-Facing Wire Clamps (Accessible Even When Another Shield is Stacked on Top)
Dimensions:
  • Single Wing Dimensions: 66.0 mm × 16.0 mm × 22.0 mm
  • Installed Span Width on UNO: ≈ 76.0 mm
  • Weight: ≈ 28 g (Pair)
Pinout and Wiring:
  • Right Wing (Digital Side): Align the 8-pin (`D0–D7`) and 8-pin/10-pin (`D8–AREF`) bottom pins with the Arduino UNO’s digital header bank so the screw terminals face outward.
  • Left Wing (Power & Analog Side): Align the 6-pin (`A0–A5`) and 6-pin (`RST–VIN`) bottom pins with the Arduino UNO’s power and analog header banks.
  • Top Shield Stacking: Plug any standard UNO shield into the pass-through female sockets on top of the two wings while routing external field wires out the sides.
  • Engineering Precaution: When removing the XD-216 wings from an Arduino UNO, rock each wing gently from end to end rather than pulling one corner sharply so you do not bend the long stackable pass-through pins.
Datasheet Reference:
Commonly Used in:
  • Stacked Shield Systems Requiring External Screw-Terminal Field Wiring
  • Mobile Robotics, Animatronics, and CNC Enclosures Subject to Vibration
  • Industrial Sensor Test Fixtures and Classroom Lab Workstations
Applications:
  • Simultaneous Shield + Screw Terminal Use: Stacks a W5100 Ethernet Shield or Data Logger Shield on top while wiring external DS18B20, relay, and float-switch leads into the side screw terminals.
  • Unobstructed DIP Chip Access: Allows swapping the 28-pin DIP ATmega328P-PU or attaching a 6-pin ICSP programmer without removing the screw terminals.
  • Permanent Exhibition Installations: Eliminates intermittent DuPont jumper disconnects in museum kiosks and escape rooms.
Equivalent Models:
  • Screw Shield V2 Terminal Expansion Board: Single-piece bridge PCB that spans across the UNO and adds a central solder perfboard grid and reset button.
  • UNO R3 / Mega 2560 Terminal Expansion Board Kit: Full 84-pin screw terminal shield supporting the extended pins of the Arduino Mega 2560.
  • Arduino UNO Sensor Shield V5.0: Breaks out UNO pins to 3-pin GVS male DuPont headers instead of screw terminals.
Package Includes:
  • 1 × XD-216 Screw Shield V1 Two-Piece Terminal Expansion Board Set for Arduino UNO
Weight 30 g

Questions and Answers

No questions have been asked about this product yet. Be the first!


Ask a Question

Average Rating
0.00
0 Reviews
5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Be the first to review “XD-216 Screw Shield V1 Two-Piece Terminal Expansion Board Set for Arduino UNO”

You must be logged in to post a review.

Reviews

No reviews yet. Be the first to share your experience!

XD-216 Screw Shield V1 Two-Piece Terminal Expansion Board Set for Arduino UNO

XD-216 Screw Shield V1 Two-Piece Terminal Expansion Board Set for Arduino UNO

₹249.00
Hi, How can I help you today?
Chat Assistant