Back to Category
Shop By Departments

5.3V 3A APM 2.5/2.6/2.8 Pixhawk Power Module with Voltage and Current Sensor

₹499.00

In stock ?

In stock

SKU: IFT00163-3 Category: Tags: , Brand:

5.3V 3A APM 2.5/2.6/2.8 Pixhawk Power Module with Voltage and Current Sensor is a flight-controller power supply (BEC) and inline battery telemetry sensor board designed for ArduPilot APM 2.5/2.6/2.8 and Pixhawk autonomous quadcopters, fixed-wing UAVs, and rovers. Connected inline with a 2S to 4S (up to 18V) LiPo flight battery, it supplies a clean switching-regulated 5.3V DC 2.25A–3A power rail alongside analog battery voltage and current-consumption measurements (up to 90A) over a single 6-pin Molex/DF13 cable to the flight controller.

Key Features:
  • Regulated 5.3V 2.25A–3A Flight Controller BEC: Switching step-down regulator delivers 5.3V DC (intentionally 0.3V above 5.0V to compensate for the APM/Pixhawk protection diode drop so the MCU receives a true 5.0V).
  • Real-Time 90A Current & 18V Voltage Sensing: Precision $0.5,text{m}Omega$ / $1,text{m}Omega$ current-sense shunt resistor and high-side amplifier output analog voltage and current telemetry for Mission Planner / QGroundControl OSD and failsafe alerts.
  • Single 6-Pin Plug-and-Play Telemetry Cable: Pre-crimped 6-position cable connects VCC (2 pins), GND (2 pins), V_SENSE, and I_SENSE directly to the `PM` (Power Module) port on APM and Pixhawk flight controllers.
  • Supports 2S to 4S LiPo Flight Packs: Operates across 6V to 18V DC battery inputs while passing up to 90A peak ESC current through heavy-gauge pads/connectors.
  • Heat-Shrink Insulated Flight-Ready Package: Compact, lightweight module insulated in clear protective heat-shrink tubing for drone frame mounting.
Technical Specifications:
  • Compatible Flight Controllers: ArduPilot APM 2.5 / 2.6 / 2.8, Pixhawk PX4 / 2.4.8, and Custom MCU Telemetry
  • Input Battery Voltage: 6.0V to 18.0V DC (2S to 4S LiPo Pack; up to 28V max sense)
  • Maximum Pass-Through Current Measurement: 90A Max
  • BEC Regulated Output Voltage: 5.3V DC ± 0.1V
  • BEC Maximum Output Current: 2.25A Continuous / 3.0A Peak
  • Voltage & Current Sense Output Scaling: 3.3V ADC Compatible (~10.1:1 Voltage Divider | ~17V/A or 18.18A/V Current Sensitivity)
Mechanical Specifications:
  • PCB & Insulation: Double-Sided Heavy-Copper PCB in Clear Heat-Shrink Sleeve
  • Flight Controller Interface: 6-Pin Molex PicoBlade / DF13 Telemetry Cable
Dimensions:
  • PCB Length: ~30 mm (excluding cables)
  • Width: ~20 mm
  • Height: ~8 mm
  • Weight: ~25 g to 35 g
Pinout and Wiring:
  • Battery Input Side (IN+ / IN-): Connect to 2S–4S LiPo flight battery.
  • ESC / PDB Output Side (OUT+ / OUT-): Connect to quadcopter power distribution board (PDB) or ESCs.
  • 6-Pin PM Cable (Pin 1 to Pin 6): Pin 1 & 2 = +5.3V VCC | Pin 3 = Current Sense (I) | Pin 4 = Voltage Sense (V) | Pin 5 & 6 = GND.
  • Servo Note: The 5.3V 2.25A BEC is designed to power the flight controller, GPS, telemetry radio, and RC receiver—do NOT use it to power high-torque wing/gimbal servos (use a dedicated 5V UBEC on the servo rail).
Datasheet Reference:
  • Telemetry Standard: ArduPilot / PX4 Analog Power Brick Specification (INA169 / ZXCT1009 Current Shunt Monitor + MP1584/LM2596 5.3V Buck Regulator)
Commonly Used in:
  • APM 2.6 / 2.8 & Pixhawk 2.4.8 Autonomous Quadcopters & Hexacopters
  • Fixed-Wing UAVs, VTOL Aircraft, and Autonomous Boats
  • ROS / ArduRover Mobile Robotics Battery Telemetry
  • Arduino / ESP32 90A High-Side DC Power Monitors
Applications:
  • Provides rock-solid 5.3V power to APM or Pixhawk flight controllers while feeding real-time battery voltage, current draw (Amps), and consumed mAh to Mission Planner and FPV OSDs.
  • Triggers automatic Return-to-Launch (RTL) battery failsafes when flight battery voltage or remaining capacity drops below your threshold.
  • Can also be wired to any 3.3V/5V Arduino or ESP32 ADC pins as a standalone 90A DC current/voltage sensor + 5.3V power supply.
Equivalent Models:
  • MINI560 DC 5V 5A Step-Down Stabilized Buck Converter Module: Pure 5V 5A UBEC step-down module without voltage/current telemetry sensing.
Package Includes:
  • 1 × 5.3V 3A APM 2.5/2.6/2.8 Pixhawk Power Module with Voltage and Current Sensor

Questions and Answers

No questions have been asked about this product yet. Be the first!


Ask a Question

Average Rating
5.00
1 Review
5 Star
100%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Add a review

You must be logged in to post a review.

1 Review For This Product

  1. by Romen Thangjam | October 9, 2022

    Ok

5.3V 3A APM 2.5/2.6/2.8 Pixhawk Power Module with Voltage and Current Sensor

5.3V 3A APM 2.5/2.6/2.8 Pixhawk Power Module with Voltage and Current Sensor

₹499.00
Hi, How can I help you today?
Chat Assistant