4V-60V DC 10A High-Power MOSFET Trigger Drive Switch Module

4V-60V DC 10A High-Power MOSFET Trigger Drive Switch Module is a versatile solid-state PWM trigger switch board capable of switching high-voltage 4V to 60V DC loads at up to 10A continuous current (up to 600W max) using either a high-level (3.0V–24V) or low-level (0V–0.6V) control signal. Featuring dual-mode trigger inputs, up to 2.5kHz PWM frequency response, and heavy-duty screw terminal blocks, it allows 3.3V/5V microcontrollers or industrial 12V/24V PLC outputs to drive high-voltage DC motors, solenoids, heaters, and LED arrays effortlessly.

Key Features:

• Wide 4V to 60V DC Load Voltage Range: Extends well beyond standard 36V MOSFET modules to support 48V telecom, e-bike, solar, and industrial actuator buses up to 60V DC.
• 10A Continuous / 600W Switching Capacity: Low-on-resistance power MOSFET switches up to 10A continuously at room temperature (up to 15A–20A with auxiliary heatsink cooling).
• Supports Both High-Level & Low-Level Triggering: Dedicated input pins accept either active-HIGH (3.0V–24V) logic/PLC signals or active-LOW (0V–0.6V) NPN open-collector triggers.
• PWM Speed & Brightness Control (0–2.5kHz): Accepts PWM duty-cycle signals up to 2.5kHz for stepless DC motor speed regulation and LED dimming.
• Arc-Free Unlimited Solid-State Lifespan: Eliminates contact bounce, clicking noise, and electromagnetic arcing of mechanical relays.

Technical Specifications:

• Operating Load Voltage: 4.0V to 60.0V DC
• Continuous Load Current: 10A (Up to 600W; add heatsink above 10A)
• High-Level Trigger Voltage: 3.0V to 24.0V DC
• Low-Level Trigger Voltage: 0.0V to 0.6V DC (Note: Do not leave trigger between 0.6V and 3.0V, as the MOSFET will operate in the linear region and overheat!)
• PWM Frequency Range: 0 Hz to 2.5 kHz
• Operating Temperature Range: -40°C to +85°C

Mechanical Specifications:

• PCB Material: FR-4 Double-Sided Fiberglass PCB
• Power Terminals: 4-Pin Screw Terminal Block (VIN+, VIN-, OUT+, OUT-)
• Control Interface: 3-Pin Trigger Header / Terminal

Dimensions:

• Length: 46 mm
• Width: 29 mm
• Height: 15 mm
• Weight: ~16 g

Pinout and Wiring:

• VIN+ / VIN-: Connect 4V–60V DC power supply positive and negative leads.
• OUT+ / OUT-: Connect 4V–60V DC load.
• Trigger Input: Connect 3.3V/5V/12V/24V GPIO or PLC trigger signal and common GND.

Datasheet Reference:

• Topology: Gate-Driver Stage + High-Voltage 60V/75V N-Channel Power MOSFET

Commonly Used in:

• 36V / 48V Industrial Solenoid Valves, Clutches, and Brakes
• 3D Printer Heated Bed & Extruder Heater External MOSFET Switches
• DC Motor PWM Speed Control & High-Power LED Dimming
• PLC Solid-State DC Output Amplifiers

Applications:

• Switches 24V, 36V, or 48V DC solenoids, water pumps, and heating cartridges from a 3.3V ESP32 or 5V Arduino GPIO pin.
• Offloads heavy heated-bed currents (8A–10A) from 3D printer controller motherboards to prevent burnt mainboard connectors.
• Replaces noisy mechanical relays in high-cycle industrial automation and lighting sequencers.

Equivalent Models:

• DC 5V-36V 15A 400W Switch Large Power MOSFET Module: Dual-MOSFET 15A module optimized for 5V–36V DC loads.
• 4-Channel IRF540 MOSFET Switch Module: Quad-channel opto-isolated MOSFET driver board.

Package Includes:

• 1 × 4V-60V DC 10A High-Power MOSFET Trigger Drive Switch Module