Back to Category
Shop By Departments

4-Channel 5V Relay Shield Module for Arduino UNO R3

₹349.00

In stock ?

In stock

SKU: SHIELD-1-8 Category: Brand:

4-Channel 5V Relay Shield Module for Arduino UNO R3 is a stackable 4-channel electromechanical power switching shield designed to plug directly atop an Arduino UNO R3, Leonardo, or Mega 2560 without jumper wires. Furthermore, it integrates four high-current 5V DC SPDT sugar-cube relays (`NO / COM / NC` screw terminals), transistor coil drivers with flyback protection diodes, four individual channel status LEDs, and wireless XBee/RF header sockets. Consequently, an Arduino UNO can safely switch four independent AC mains lamps, fans, solenoid valves, or DC motors right from its digital output pins.

Key Features:
  • Four Independent SPDT Power Relays: Each relay provides Normally Open (`NO`), Common (`COM`), and Normally Closed (`NC`) 3-pin screw terminals for flexible high-side or low-side load switching.
  • Direct Plug-In UNO Shield Design: Eliminates loose breadboard wires between the Arduino and relay driver transistors by routing control signals internally through the stackable headers.
  • Transistor-Driven Coils with Flyback Diodes: NPN driver transistors and 1N4148 freewheeling diodes isolate the Arduino GPIO pins from inductive relay coil kickback.
  • Visual Channel Diagnostics: Four individual red SMD LEDs (`REL1–REL4`) illuminate immediately whenever their corresponding relay coil is energized.
  • Bonus Wireless & Sensor Expansion Headers: Includes onboard female headers for XBee / Bluetooth wireless modules and 3-pin analog/digital sensor pass-throughs.
Technical Specifications:
  • Compatible Host Boards: Arduino UNO R3, Leonardo R3, Mega 2560 R3
  • Number of Relay Channels: 4 Independent SPDT (1 Form C) Channels
  • Relay Coil Voltage: 5.0V DC ( ~70 mA per Energized Relay Coil; ~280 mA with All 4 Relays ON)
  • Contact Switching Rating: Up to 3A–10A @ 125V/250V AC or 30V DC (Depending on Subminiature Relay Sub-Type; Recommended ≤2A for Inductive Loads)
  • Output Terminals: 4 × 3-Position Rising-Clamp Screw Terminal Blocks (`NOn, COMn, NCn`)
  • Default Control Pin Mapping: Digital Pins `D7, D6, D5, D4` (or `D2–D5` / Jumper Configurable Depending on Revision; Printed on Silkscreen)
  • Trigger Logic: Active-High (`HIGH` = Relay Energized / `NO` Closed to `COM`)
Mechanical Specifications:
  • PCB Substrate: Double-Sided Red/Blue FR-4 Fiberglass PCB with Slotted High-Voltage Isolation Cutouts Under Relay Contacts
  • Screw Terminal Pitch: 3.5 mm / 5.0 mm Heavy-Duty Terminal Blocks
  • Onboard Controls: Top-Mounted Hardware Reset Button
Dimensions:
  • Length: 68.6 mm
  • Width: 53.4 mm
  • Height: 24.0 mm
  • Weight: ≈ 52 g
Pinout and Wiring:
  • Digital Control Pins (`J1–J4`): Driven by Arduino digital pins `D7 (Relay 1), D6 (Relay 2), D5 (Relay 3), D4 (Relay 4)` (check top silkscreen next to the `J1–J4` header jumpers).
  • Load Terminal Wiring (`NO / COM / NC`): For a load that should stay OFF by default and turn ON when triggered, wire the power source hot/positive line into `COM` and the load hot/positive lead into `NO` (Normally Open).
  • External 9V DC Supply Recommendation: When energizing all 4 relays simultaneously (~280mA total coil current), power your Arduino UNO from a 7.5V–9V DC barrel-jack adapter or a ≥1A USB port.
  • Engineering Precaution: Before stacking this shield onto an Arduino UNO that has a large metal USB Type-B port, stick two layers of insulating electrical tape on top of the UNO’s metal USB-B shell so the relay terminal solder pins on the bottom of the shield can never touch the grounded USB housing!
Datasheet Reference:
Commonly Used in:
  • Smart Home Appliance, Lighting, and Exhaust Fan Automation
  • Automated Greenhouse Solenoid Valve, Water Pump, and Grow-Light Controllers
  • Industrial Access Control Door Strikes, Buzzers, and Pneumatic Valves
Applications:
  • 4-Zone Irrigation & Hydroponics Timer: Pairs with an I2C RTC module to sequence four 12V/24V solenoid water valves and nutrient dosing pumps.
  • Wireless Bluetooth / XBee Relay Switcher: Plugs an HC-05 Bluetooth or XBee module directly into the shield’s wireless header to toggle 4 relays from a smartphone app.
  • Benchtop Automated Burn-In Cycling: Cycles power to 4 Device-Under-Test (DUT) units thousands of times to test hardware reliability.
Equivalent Models:
  • Standalone 4-Channel 5V Opto-Isolated Relay Module: Separate PCB board with 10A Songle relays that connects via 6 DuPont jumper wires instead of stacking directly atop an UNO.
  • 8-Channel 5V Relay Module Board: Doubles capacity to 8 channels for larger Arduino Mega automation cabinets.
  • 4-Channel Solid State Relay (SSR) Module: Silent zero-crossing triac module for high-frequency AC switching without mechanical relay click.
Package Includes:
  • 1 × 4-Channel 5V Relay Shield Module for Arduino UNO R3
Weight 50 g

Questions and Answers

No questions have been asked about this product yet. Be the first!


Ask a Question

Average Rating
0.00
0 Reviews
5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Be the first to review “4-Channel 5V Relay Shield Module for Arduino UNO R3”

You must be logged in to post a review.

Reviews

No reviews yet. Be the first to share your experience!

4-Channel 5V Relay Shield Module for Arduino UNO R3

4-Channel 5V Relay Shield Module for Arduino UNO R3

₹349.00
Hi, How can I help you today?
Chat Assistant