30A Dual DC Motor Monster Motor Shield VNH2SP30 is an ultra-high-power dual-channel DC motor driver expansion board engineered for demanding robotics, heavy electric vehicle prototypes, and high-torque automated machinery. Powered by a pair of STMicroelectronics VNH2SP30 automotive-grade integrated full-bridge motor drivers, this board delivers an impressive continuous current of 14A per channel (with a massive 30A peak surge rating) across a wide 5.5V to 16V DC supply rail. Featuring onboard current sensing feedback, thermal shutdown, and PWM speed regulation up to 20 kHz, it provides robust motor actuation without excessive acoustic noise or power loss.
Key Features:
- Dual VNH2SP30 Automotive Drivers: Houses two monolithic H-bridge ICs capable of delivering 14A continuous and 30A peak current per motor.
- High-Frequency 20kHz PWM: Supports ultrasonic switching frequencies up to 20 kHz, completely eliminating irritating audible motor whine.
- Integrated Current Sense Feedback: Dedicated analog output pins deliver real-time motor current telemetry for load monitoring and stall detection.
- Automotive-Grade Protection: Built-in overvoltage clamp, undervoltage shutdown, thermal protection, and cross-conduction prevention.
- Arduino Shield Compatibility: Designed with stackable header pin spacing for direct or jumper-wired interfacing with Arduino and 5V microcontrollers.
Technical Specifications:
- Operating Motor Voltage (VCC): 5.5V to 16.0V DC (absolute max 40V surge)
- Continuous Output Current: 14.0 A per channel (continuous with proper heatsinking)
- Peak Surge Output Current: 30.0 A per channel (pulsed)
- Current Sense Ratio: Approximately 0.13V per Ampere output
- Maximum PWM Frequency: 20 kHz
- MOSFET On-State Resistance: Ultra-low 19 mΩ per switch
- Thermal Shutdown Threshold: 175°C internal die temperature
Mechanical Specifications:
- PCB Architecture: Heavy 2oz copper double-sided FR4 board designed for high thermal dissipation
- Power & Motor Terminals: Large 5.0mm screw terminal blocks or heavy-gauge direct solder pads
- Mounting Holes: 4 × 3.2mm perimeter chassis mounting holes
Dimensions:
- Length: 53.0 mm
- Width: 60.0 mm
- Height: 12.5 mm
- Weight: Approximately 32 g
Pinout and Wiring:
- +5V: Logic supply input from microcontroller.
- GND: Common system ground.
- +5V / VIN (Power Terminals): Heavy-duty DC battery connection (5.5V to 16V DC).
- OUTA1 / OUTA2: High-current output terminals for Motor 1.
- OUTB1 / OUTB2: High-current output terminals for Motor 2.
- INA1 / INA2: Directional logic inputs for Motor 1.
- INB1 / INB2: Directional logic inputs for Motor 2.
- PWMA / PWMB: PWM speed control inputs (up to 20kHz).
- CS_A / CS_B: Analog current sense feedback outputs.
- EN_A / EN_B: Status enable and diagnostic fault alert pins.
Datasheet Reference:
Commonly Used in:
- Combat & Heavyweight Robots: High-impact battle bots, heavy rovers, and planetary rover prototypes.
- Electric Golf Carts & Wheelchairs: High-torque traction drive motor speed and direction regulation.
- High-Torque Linear Actuators: Heavy industrial positioning rams and motorized solar tracking arrays.
Applications:
- High-Power Brushed DC Driving: Smooth proportional speed and bidirectional control for RS775, RS550, and wheelchair motors.
- Closed-Loop Current Limiting: Active stall detection and torque limiting using analog current sense telemetry.
- Heavy Automation: Robotic arm base rotation and heavy motorized conveyor positioning.
Equivalent Models:
- BTS7960 43A High-Power Motor Driver: Infineon half-bridge module handling higher operating voltages up to 27V DC and 43A peak current.
- VNH5019 Dual Motor Driver Shield: Upgraded STMicroelectronics successor supporting up to 24V DC operating voltage with enhanced reverse-battery protection.
- L298N Dual Motor Driver: Lower-power entry alternative (2A per channel) for small tabletop robotics projects.
Package Includes:
- 1 × 30A Dual DC Motor Monster Motor Shield VNH2SP30

Reviews
No reviews yet. Be the first to share your experience!