Back to Category
Shop By Departments

L6219DS Dual Full-Bridge Stepper Motor Driver IC – SOIC-24

₹190.72

In stock ?

L6219DS Dual Full-Bridge Stepper Motor Driver IC in SOIC-24 package for driving bipolar stepper motors and DC motors up to 46V 750mA.

In stock

Category:

L6219DS Dual Full-Bridge Stepper Motor Driver IC – SOIC-24 is a monolithic integrated dual full-bridge motor driver designed to drive both windings of a bipolar stepper motor or bidirectionally control two independent brushed DC motors. Fabricated using high-voltage BCD (Bipolar, CMOS, DMOS) technology, the IC integrates two independent DMOS H-bridges capable of delivering continuous load currents up to 750 mA (with 1.0 A peak) across a broad motor supply voltage range of 10V to 46V. Each bridge incorporates internal pulse-width modulation (PWM) current-control circuitry regulated via external sense resistors and DAC voltage references, built-in flyback recirculation diodes, thermal shutdown protection, and cross-conduction shoot-through suppression. Packaged in a compact 24-pin batwing surface-mount SOIC envelope, it is ideally suited for automated office equipment, industrial automation, robotics, and precision motion control.

Key Features:
  • Dual Full-Bridge H-Bridge Architecture: Capable of driving two phases of a bipolar stepper motor or two separate DC motors with bidirectional rotation.
  • Wide Motor Operating Voltage: Operates across an expansive motor supply voltage range from 10V to 46V DC with sustaining capability up to 50V transients.
  • Integrated PWM Current Control: Internal peak-current chopping circuitry regulates phase currents using external current-sensing resistors and reference voltages.
  • Digital Current Scaling Logic: Two digital inputs per bridge (I0 and I1) configure load current limits to 100%, 67%, 33%, or 0% (disable) for full-step, half-step, and microstepping modes.
  • Internal Protection & Suppression Diodes: Equipped with integrated ground-clamp and flyback inductive recirculation diodes, thermal shutdown protection, and anti-cross-conduction dead-time logic.
Technical Specifications:
  • Supply Voltage (Logic VCC): 4.5V to 5.5V DC (5.0V typical)
  • Supply Voltage (Motor Load VBB): 10V to 46V DC
  • Continuous Output Current per Channel: 750 mA (0.75 A)
  • Peak Output Current per Channel: 1.0 A (non-repetitive startup / pulse)
  • Output Saturation Voltage (Source + Sink): 2.4V typical at 750 mA load
  • Logic Input High Voltage (VIH): 2.0V minimum (5V TTL / CMOS compatible)
  • Logic Input Low Voltage (VIL): 0.8V maximum
  • Reference Input Voltage Range (VREF): 0V to 2.5V DC
  • PWM Off-Time Range: Programmable via external RC network on RC1 / RC2 pins
  • Thermal Shutdown Threshold: 165°C typical with hysteresis
  • Operating Ambient Temperature Range: -20°C to 85°C
  • Storage Temperature Range: -55°C to 150°C
Mechanical Specifications:
  • Package Type: SOIC-24 (Small Outline Integrated Circuit, 24 Leads, Batwing Leadframe)
  • Mounting Type: Surface Mount Device (SMD / SMT)
  • Leadframe Structure: Pins 10, 11, 23, and 24 internally fused to ground for enhanced heatsinking to PCB copper planes
  • Body Material: Molded epoxy encapsulation (UL94-V0 flame-retardant)
  • Lead Finish: Matte Tin (Sn) lead-free plating, RoHS compliant
  • Net Weight: Approximately 0.65 g
Dimensions:
  • Package Body Length: 15.4 mm ± 0.2 mm
  • Package Body Width: 7.5 mm ± 0.2 mm
  • Total Width (Including Leads): 10.3 mm ± 0.3 mm
  • Package Overall Height: 2.65 mm maximum
  • Lead Pitch: Standard 1.27 mm (0.050 inch) spacing
Pinout and Wiring:
  • Power Supply Rails: V_BB (Pin 12) provides high-voltage motor supply (10V to 46V DC); V_CC (Pin 13) provides regulated 5V logic supply.
  • Ground & Thermal Fused Leads: GND (Pins 10, 11, 23, 24) provide common circuit ground and internal heat sinking to PCB copper planes.
  • Bridge 1 Outputs & Sensing: OUT 1A (Pin 1) & OUT 1B (Pin 4) drive Phase A motor winding; SENSE 1 (Pin 3) connects to ground via external current-sense resistor; COMP IN 1 (Pin 2) receives filtered sense feedback.
  • Bridge 2 Outputs & Sensing: OUT 2A (Pin 22) & OUT 2B (Pin 19) drive Phase B motor winding; SENSE 2 (Pin 20) connects to ground via external current-sense resistor; COMP IN 2 (Pin 21) receives filtered sense feedback.
  • Logic Control & Reference: PHASE 1 & 2 (Pins 7, 16) determine winding direction; I0 & I1 (Pins 5, 6, 17, 18) set peak current thresholds (0%, 33%, 67%, 100%); V_REF 1 & 2 (Pins 8, 15) and RC 1 & 2 (Pins 9, 14) set reference levels and PWM off-time.
Datasheet Reference:
  • Manufacturer Specification: STMicroelectronics L6219 / E-L6219DS Stepper Motor Driver Technical Datasheet
  • Cross-Reference Specification: Allegro MicroSystems L6219DS / L6219DS-T Motor Driver Reference Manual
  • Application Note: Driving Bipolar Stepper Motors with PWM Current Chopping Control Architecture
Commonly Used in:
  • Printers, document scanners, photocopy machines, and ticketing automation mechanisms.
  • Medical infusion pumps, laboratory fluid handling equipment, and automated optical stages.
  • Security surveillance pan-tilt-zoom (PTZ) camera positioning drives.
  • Textile sewing machines, automated embroidery equipment, and CNC feeder axes.
Applications:
  • Bipolar Stepper Motor Actuation: Driving two-phase permanent magnet or hybrid stepper motors with microstepping resolution.
  • Bidirectional DC Motor Driving: Operating two independent brushed DC motors with full speed and direction control.
  • Precision Open-Loop Motion Control: Indexing optical carriages, paper feeders, and robotic linear actuators without encoder feedback.
  • Industrial Solenoid & Valve Driving: Actuating high-voltage inductive solenoids with controlled peak holding current.
Equivalent Models:
  • STMicroelectronics E-L6219DS: RoHS-compliant lead-free version of L6219DS sharing identical pinout and electrical specifications.
  • Allegro L6219DSTR-T: Fully pin-compatible and function-compatible equivalent driver IC in SOIC-24 package.
  • TBD62083AFNG: 8-channel DMOS transistor array offering high-voltage low-side sink driving without integrated H-bridge topology.
  • L298N Dual Full-Bridge Driver: Higher-current dual H-bridge driver IC capable of up to 2A per channel but lacking integrated PWM current chopping comparators.
Package Includes:
  • 1 × L6219DS Dual Full-Bridge Stepper Motor Driver IC – SOIC-24
Weight 1 g

Questions and Answers

No questions have been asked about this product yet. Be the first!


Ask a Question

Average Rating
0.00
0 Reviews
5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Be the first to review “L6219DS Dual Full-Bridge Stepper Motor Driver IC – SOIC-24”

You must be logged in to post a review.

Reviews

No reviews yet. Be the first to share your experience!

L6219DS Dual Full-Bridge Stepper Motor Driver IC – SOIC-24

L6219DS Dual Full-Bridge Stepper Motor Driver IC – SOIC-24

₹190.72
Hi, How can I help you today?
Chat Assistant