NAZE32 6DOF RACING FLIGHT CONTROLLER BOARD WITH CASE

• No compromise I/O. Use all the features all the time; e.g. Connect your OSD + SmartPort + SBus + GPS + LED Strip + Battery Monitoring + Sonar + 8 motors – all at the same time!
• On-board high-capacity black box flight log recorder – optimize your tuning and see the results of your setup without guesswork (Standard and Deluxe).
• Next-generation STM32 F1 processor with hardware floating point unit for efficient flight calculations and faster.
• Stackable design – perfect for integrating with OSDs and power distribution boards.
• 16 PWM I/O lines for ESCs, Servos and legacy receivers. 8 available on standard pin headers. 8 via side mounted connectors.

Naze 32 versions explained and what to look out for

There are currently four core versions of the naze 32 flight controller. These are referred to as Acro 1.1k, 6 DOF, 10 DOF, and Full 3.3k. All the versions use the same basic hardware such as the STM32F103CBT6 CPI running at 72Mhz with 16Mb of flash memory. The sensors is where each of the versions differ as shown in the table below. The different sensors on the various versions mean that the boards can be manufactured more cheaply which appeals to certain applications.

Naze 32 6 DOF – this is the cheapest level naze 32 flight controller and does not include a magnetometer sensor or a barometer. Ideal for experianced FPV pilots who want a cheap but capable flight controller

Naze 32 Acro – this version adds a BMP280 barometer to the board which only increases the price by £1-2. However the added barometer means that the flight controller can perform altitude hold functions which is particularly useful for less experienced pilots.

Naze 32 10 DOF – This board includes both the BMP280 barometer and a HMC5833 compass sensor. Adding a compass sensor helps with getting better aircraft heading measurements while you are flying, but most importantly it allows you to add a GPS module to enable position hold flight mode with your drone.

Naze 32 Full – The full version is the same as the 10 DOF except that it uses much better quality sensors, the MS6511 barometer and MHC5983 compass are much more accurate. However these sensors cost more so the Naze 32 full flight controller is the most expensive option, but has the best performance.

Built in SPI Dataflash
All the revision 6 boards include a built in black box flight data recorder which is great. The 6 DOF, Acro and 10 DOF naze boards have 16Mbit onboard SPI flash. However the Full version includes 128Mbit onboard SPI flash so this just means you can store more flight logs on your full board.

• Full support for OneShot ESCs for easy PID tuning and a sharper response.
• Supports SBus, SumH, SumD, spektrum 11024/2048, XBus, PPM, PWM receivers. No external inverters required (built-in).
• Dedicated output for programmable LEDs – great for orientation, racing and night flying.
• Dedicated I2C port for connection of OLED display without needing flight battery.
• Battery monitoring ports for voltage and current.
• Sonar support for precision low-altitude hold.
• Buzzer port for audible warnings and notifications.
• Developer friendly debugging port (SWD) and boot mode selection, unbrickable bootloader.
• Symmetrical design for a super tidy wiring.
• Wire up using pin headers, JST-SH sockets or solder pads. Use either right-angled or straight pin-headers.
• without Barometer and magnetometer.
• Loop times up to ~2x as fast as previous-generation STM32F1 based boards.
• Configuration of the flight controller via a cross-platform GUI (Windows / OSX / Linux).
• Supports a variety of aircraft, tricopters, quadcopters, hexacopters, octocopters, planes and more.
• The SPRacingF3 runs the open-source Cleanflight flight control (FC) software which has an ever-growing community of friendly developers and users. Being open-source means that you too can contribute to the system.
  NAZE32 Acro SP Racing F3 Flight Controller For DIY 250 RC Quadcopter FPV MulticopterRacing F3 Flight Controller (SPRacingF3) was designed to give awesome flight performance based on tried and tested sensors whilst also providing unparalleled I/O capabilities in a small and extremely lightweight form-factor using a next-generation CPU. The SPRacingF3 gives you all the features you need for the heart of your aircraft, whether you’re into FPV racing, acrobatic flying or aerial photography it’s perfect.Specifications:
  Colour: black
  Material: ABS + metal
  Model: SPRacingF3 (Standard version)
  Processor: stm32f3 CPU
  USB: Micro USB socket